Home > Knowledge > Content

Aluminum alloy

Jul 06, 2022

Aluminum alloy

Material component seeks Baidu directly, we won't make the list. The density of aluminum alloy is 2.63 ~ 2.85g/cm, and it has high strength (σb is 110 ~ 270MPa). The specific strength is close to that of high alloy steel, but the specific stiffness is higher than that of steel. It has good casting and plastic processing properties, good electrical and thermal conductivity properties, good corrosion resistance and weldability. 


The fluidity of the die-cast aluminum alloy is better, and the melting point is 660℃. 

Aluminum alloy in the product structure design process application form is also the most abundant, commonly used processing technology: die casting, extrusion molding, machining, stamping, forging. Aluminum alloy profiles are widely used in building doors and windows, and aluminum profiles are also commonly used to build frames for mechanical equipment. Electronic products and life of FMCG shell is also no lack of aluminum alloy, this kind of product appearance requirements are higher, the more common process is extrusion, machining, stamping and so on. Die-cast aluminum is seldom used in the shell of FMCG, because the die-cast aluminum alloy contains high Si, so when Anodizing, it directly reacts with the liquid medicine, and the surface effect after oxidation is poor. Aluminum castings are often used for internal structural parts and parts with low requirements on appearance. The engine shell of a motorcycle needs a complex structure, lightweight and sufficient strength. Most of the rotating aluminum alloy die casting is used as the blank material.


Aluminum cast engine housing: 

Aluminum brand number means as below:

1××× series: pure aluminum (aluminum content is not less than 99.00%), the last two digits of this series is expressed as the percentage point of the lowest aluminum content. The second letter of the brand indicates the modification of the original pure aluminum. 

The last two digits of the 2××× ~ 8××× series are of no special significance and are only used to distinguish different aluminum alloys in the same group. The second letter of the label indicates the modification of the original pure aluminum. 

2××× series: aluminum alloy with copper as the main alloying element. 2011 fast cutting alloy, good machinability and high strength. 2018 2218 alloy for forging, good forgability and high high temperature strength. 

3××× series: aluminum alloy with manganese as the main alloying element. Building materials, colored aluminum plate, bottle cap. 

4××× series: aluminum alloy with silicon as the main alloying element. 4032 heat resistance, resistance to friction and reduction, small thermal expansion coefficient. Piston, cylinder head. 

5××× series: aluminum alloy with magnesium as the main alloying element. 5052 is the most representative alloy of medium strength, common sheet metal, ship, vehicle, construction, bottle cap, honeycomb plate. 6××× series is aluminum alloy with magnesium as the main alloying element and Mg2Si phase as strengthening phase. 6063 typical alloy for extrusion, the strength is lower than 6061, good extrusion, can be used for complex section shape of the shape of the material, corrosion resistance and surface treatment are good construction, highway guardrail, high fence, vehicles, furniture, household appliances, ornaments. 7××× series: aluminum alloy with zinc as the main alloying element. 7075 aluminum alloy has one of the highest strength alloy, but the corrosion resistance is not good, and 7072 covered skin can improve its corrosion resistance, but the cost is higher. Aircraft, ski poles. 

8××× series: aluminum alloy with other elements as the main alloying elements

9××× series: reserve alloy group


Aluminum alloys with tensile strength greater than 480MPa are called high-strength aluminum alloys, mainly based on Al-Cu-Mg and Al-Zn-Mg-Cu alloys, namely 2XXX (duralumin) and 7XXX (super duralumin) alloys. The static strength of the former is slightly lower than the latter, but the service temperature is higher than the latter. The properties of alloys vary greatly due to their chemical composition, melting and solidification methods, processing technology and heat treatment system.


Send Inquiry
Contact Us
  • Oversea Trading Office
  • Hong Kong Longqing Metals Products Works Limited
  • James Venosa (Global Sourcing Manager)
  • Tel.01-431-335-7268
  • E-mail: jamesv@lqtitanium.com
  • Address: Unit 89,3/F., Yao Lee Center, No.45 Hoi Yuen Road, Kwun Tong, Kowloon, HK
  •  
  • Processing Factory
  • Baoji Longqing Metals Products Works
  • Misty Guo (Oversea Trading Manager)
  • Tel.86-151-2937-4292
  • Email: mistyg@lqtitanium.com
  • Address: 321 Gaoxin Avenue, High-Tech District, Baoji, Shaanxi, China